Select Category
_0x200.jpg)
Jr Products Pleated Shade Hold-Down, 2/Pk - 81705 - 342-81705F1
Used to secure the tension cords of your pleated shades, this hold-down comes complete with spacer and attaching screw to repair or replace any extended hold-down unit. Lifetime warranty.
Jr Products Plastic Window Crank, 1" - 20205 - 342-20205F1
Replacement window crank will fit most applications. They are made of durable polypropylene for long lasting use and come with a replacement screw. Lifetime warranty.
Jr Products Plastic Window Crank, 1-3/8" - 20215 - 342-20215F1
Replacement window crank will fit most applications. They are made of durable polypropylene for long lasting use and come with a replacement screw. Lifetime warranty.
Jr Products Plastic Window Crank, 1-3/4" - 20225 - 342-20225F1
Replacement window crank will fit most applications. They are made of durable polypropylene for long lasting use and come with a replacement screw. Lifetime warranty.
Jr Products Plastic T-Style Door Holder, 6" Polar White - 10444 - 342-10444F1
Direct replacement for your original equipment. Constructed of durable plastic for longer life. Mounting screws included. Lifetime warranty.
Jr Products Plastic T-Style Door Holder, 6" Colonial White - 10454 - 342-10454F1
Direct replacement for your original equipment. Constructed of durable plastic for longer life. Mounting screws included. Lifetime warranty.
Jr Products Plastic T-Style Door Holder, 6" Black - 10434 - 342-10434F1
Direct replacement for your original equipment. Constructed of durable plastic for longer life. Mounting screws included. Lifetime warranty.
Jr Products Plastic T-Style Door Holder, 3.5" Polar White - 10414 - 342-10414F1
Direct replacement for your original equipment. Constructed of durable plastic for longer life. Mounting screws included. Lifetime warranty.
Jr Products Plastic T-Style Door Holder, 3.5" Colonial White - 10424 - 342-10424F1
Direct replacement for your original equipment. Constructed of durable plastic for longer life. Mounting screws included. Lifetime warranty.
Jr Products Plastic T-Style Door Holder, 3.5" Black - 10324 - 342-10324F1
Direct replacement for your original equipment. Constructed of durable plastic for longer life. Mounting screws included. Lifetime warranty.
Jr Products Plastic Rosettes, White, 14/Pk - 20455 - 342-20455F1
Plastic Rosettes are commonly found in use with ceiling panels but can also be used anywhere a decorative look is desired. Their larger diameter gives the screw more surface coverage and a more secure application. Mounting screws included. Lifetime warranty.
Jr Products Plastic Rosettes, Clear, 14/Pk - 20465 - 342-20465F1
Plastic Rosettes are commonly found in use with ceiling panels but can also be used anywhere a decorative look is desired. Their larger diameter gives the screw more surface coverage and a more secure application. Mounting screws included. Lifetime warranty.
Jr Products Philips Style Rv Screen Door Latch - 11215 - 342-11215F1
Universal Secures the screen door to the entry doorDirect replacement for Philips style doorsMounting holes are 2.30" on centerMounting screws includedLifetime warranty
Jr Products Philips Style Rv Screen Door Latch - 11205 - 342-11205F1
Universal Secures the screen door to the entry doorDirect replacement for Philips style doorsMounting holes are 2.30" on centerMounting screws includedLifetime warranty
Jr Products Momentary-On/Off Switch, Black - 12705 - 342-12705F1
Ratings: SPST, 13 Amps @ 125 VAC, 10 Amps @ 250 VAC, 1/2 H.P., 5 Amps @ 14 VDCUL/CSA/RoHS approvedCutout: 1.125" x .550"Switch: 1.120" x .547"
Jr Products Mini On/Off/On Switch - 13345 - 342-13345F1
Ratings: DPDT, 13 Amps @ 125 VAC, 10 Amps @ 250 VAC, 1/2 H.P. @ 125-250 VAC, 5 Amps @ 14 VDCUL/CSA/RoHS approvedCutout: 0.745" x 0.500"Switch: 0.756" x 0.508"
Jr Products Mini On/Off/On Switch - 13335 - 342-13335F1
Ratings: SPDT 13 Amps @ 125 VAC, 10 Amps @ 250 VAC, 1/2 H.P. @ 125-250 VAC, 5 Amps @ 14 VUL/CSA/RoHS approvedCutout: 0.745" x 0.500"Switch: 0.756" x 0.508"
Jr Products Mini On/Off Switch - Spst - 13645 - 342-13645F1
SPST, 16 Amp @ 125 VAC, 16 Amp @ 250 VAC, 3/4 H.P. @ 125-250 VAC, 10 Amp @ 14 VDCUL/CSA/VDE approvedCutout: 0.756" x 0.508"Switch: 0.745" x 0.500"
Jr Products Mini Mom-On/Off/Mom-On Switch - 13725 - 342-13725F1
Ratings: SPDT 16 Amps @ 125 VAC, 1/3 H.P., 10 Amps @ 250 VAC, 1/2 H.PUL/CSA/RoHS approved0.745" x 0.500"Switch: 0.756" x 0.508"
Jr Products Mini Mom-On/Off/Mom-On Switch - 13445 - 342-13445F1
Ratings: DPDT, 13 Amp @ 125 VAC, 10 Amp @ 250 VAC, 1/2 H.P. @ 125-250 VAC, 5 Amp @ 14 VUL/CSA/RoHS approvedCutout: 0.745" x 0.500"Switch: 0.756" x 0.508"
Jr Products Mini Mom-On/Off Switch - 12815 - 342-12815F1
Ratings: SPST, 13 Amps @125 VAC, 10 Amps @ 250 VAC, 1/2 H.P. @ 125-250 VAC, 5 Amps @ 14 VDCUL/CSA/RoHS approvedCutout: 0.745" x 0.500"Switch: 0.756" x 0.508"
Jr Products Mini Labeled On/Off Switch - 13735 - 342-13735F1
DPST, 20 Amp @ 125 VAC, 15 Amp @ 250 VAC, 40 Amp Peak/20 Amp continuous @ 12 VDCUL/CUL/RoHS approvedCutout: 0.756" x 0.508"Switch: 0.745" x 0.500"
Jr Products Mini Illuminated On/Off Switches - 120V, Spst - 12765 - 342-12765F1
Illuminates when switch is in the "on" positionSPST, 10 Amps @ 125 VAC, 6 Amps @ 250 VAC, 15 Amps @ 12 VDCUL/CSA/VDE approvedCutout: 0.745" x 0.500"Switch: 0.756" x 0.508"
Jr Products Mini Blind Brackets - 81915 - 342-81915F1
Snap shut front for easier use ID 1"H x 1"WMounting screws includedLifetime warranty
Jr Products Mini 12V On/Off Switches, Black/Black - 12785 - 342-12785F1
SPST, 16 Amp @ 125 VAC, 16 Amp @ 250 VAC, 3/4 H.P. @ 125-250 VAC, 10 Amp @ 14 VDCUL/CSA/VDE approvedCutout: 0.756" x 0.508"Switch: 0.745" x 0.500"
Jr Products Metal Vent Crank - 20305 - 342-20305F1
Replacement Metal Vent Crank will fit most applications. Made of die cast steel for long lasting use and comes with a replacement screw. Lifetime warranty.
Jr Products Metal T-Style Door Holder, 6" - 10505 - 342-10505F1
Constructed of zinc plated steel Replaces any T-Style door holderMounting screws includedLifetime warranty
Jr Products Metal T-Style Door Holder, 4" - 10495 - 342-10495F1
Constructed of zinc plated steel Replaces any T-Style door holderMounting screws includedLifetime warranty
Jr Products Metal Floor Registers, White Undampered - 02-28945 - 342-0228945F1
Constructed of durable steel Long lasting powder coated colorsOEM replacement sizesEasy, one hand damper operationScrew hole for secure installationUndampered version has an extra collar depth for better air control
Jr Products Metal Floor Registers, White Undampered - 02-28925 - 342-0228925F1
Constructed of durable steel Long lasting powder coated colorsOEM replacement sizesEasy, one hand damper operationScrew hole for secure installationUndampered version has an extra collar depth for better air control
Jr Products Metal Floor Registers, White Dampered - 02-28905 - 342-0228905F1
Constructed of durable steel Long lasting powder coated colorsOEM replacement sizesEasy, one hand damper operationScrew hole for secure installation
Jr Products Metal Floor Registers, Brown Undampered - 02-28995 - 342-0228995F1
Constructed of durable steel Long lasting powder coated colorsOEM replacement sizesEasy, one hand damper operationScrew hole for secure installationUndampered version has an extra collar depth for better air control
Jr Products Metal Floor Registers, Brown Undampered - 02-28955 - 342-0228955F1
Constructed of durable steel Long lasting powder coated colorsOEM replacement sizesEasy, one hand damper operationScrew hole for secure installationUndampered version has an extra collar depth for better air control
Jr Products Metal Floor Registers, Brown Dampered - 02-28975 - 342-0228975F1
Constructed of durable steel Long lasting powder coated colorsOEM replacement sizesEasy, one hand damper operationScrew hole for secure installation
Jr Products Metal Floor Registers, Brown Dampered - 02-28915 - 342-0228915F1
Constructed of durable steel Long lasting powder coated colorsOEM replacement sizesEasy, one hand damper operationScrew hole for secure installation
Jr Products Low Profile Rv Slide Out Switch With Bezel - 12355 - 342-12355F1
Mom-On/Off/Mom-OnUse with wiring harness #13061Preprinted slide room plate12 V 40 Amp continuousCutout: 1.67" x 0.95"Switch: 2.87" x 1.87"Black
Jr Products Low Profile Rv Slide Out Switch With Bezel - 12345 - 342-12345F1
Mom-On/Off/Mom-OnUse with wiring harness #13061Preprinted slide room plate12 V 40 Amp continuousCutout: 1.67" x 0.95"Switch: 2.87" x 1.87"White
Jr Products Low Profile Bumper Door Holder - 10665 - 342-10665F1
Polymer plastic stem and rubber socket Will not fadeMounting screws includedLifetime warranty
Jr Products Low Pressure 2-Stage Automatic Changeover Regulator - 07-31525 - 342-0731525F1
Compact version Automatically redirects LP gas vapor flow from an empty designated service cylinder to a reserve cylinder without interruptionGreen indicator dome changes to red when the service cylinder needs to be filled1/4" Inverted Flare Inlet Connections3/8" FPT Outlet ConnectionZinc Die CastMolded Rubber DiaphragmsUL Approved2nd Stage Relief Mechanism Per UL 144Powder Coated
Jr Products Low Pressure 2-Stage 195,000 Btu/Hr Lp Rv Gas Regulator - 07-30385 - 342-0730385F1
Ideally designed for RV applications, these regulators ensure a smooth and continuous flow of gas to all appliances. Combines both a high pressure first stage and a low pressure second stage regulator into one unit. Zinc Die CastMolded Rubber DiaphragmsUL Approved2nd Stage Relief Mechanism Per UL 144Adjustable Screw and Dust Cap DesignPowder Coated
Jr Products Low Pressure 2-Stage 195,000 Btu/Hr Lp Rv Gas Regulator - 07-30365 - 342-0730365F1
Ideally designed for RV applications, these regulators ensure a smooth and continuous flow of gas to all appliances. Combines both a high pressure first stage and a low pressure second stage regulator into one unit. Zinc Die CastMolded Rubber DiaphragmsUL Approved2nd Stage Relief Mechanism Per UL 144Adjustable Screw and Dust Cap DesignPowder Coated
Jr Products Large Window Latch - 81875 - 342-81875F1
Replaces most top mounted groove strike latches 2.25" mounting patternMounting screws includedLifetime warranty
Jr Products Large Sliding Eye Curtain Carrier, Type A - 81085 - 342-81085F1
Lifetime warranty.
Jr Products Large Rv Kitchen Sink Strainer - 95295 - 342-95295F1
Fits any sink opening 3-1/2" - 4" Constructed of plastic or stainless steelIncludes: strainer, rubber washer and lock nut
Jr Products Large Rv Kitchen Sink Strainer - 95285 - 342-95285F1
Fits any sink opening 3-1/2" - 4" Constructed of plastic or stainless steelIncludes: strainer, rubber washer and lock nut
Jr Products Large Cabinet Strike - 70445 - 342-70445F1
Lifetime Warranty.
Jr Products Labeled 12V On/Off Switch, White - 12585 - 342-12585F1
Ratings: SPST, 16 Amps @125 VAC, 12 Amp @ 250 VAC, 3/4H.P. @ 125-250 VAC, 10 Amps @ 14VDCUL/CSA/VDE/RoHS approvedCutout: 1.125" x .550"Switch: 1.120" x .547"
Jr Products Labeled 12V On/Off Switch, Brown - 12605 - 342-12605F1
Ratings: SPST, 16 Amps @125 VAC, 12 Amp @ 250 VAC, 3/4H.P. @ 125-250 VAC, 10 Amps @ 14VDCUL/CSA/VDE/RoHS approvedCutout: 1.125" x .550"Switch: 1.120" x .547"
Jr Products Labeled 12V On/Off Switch, Black - 12615 - 342-12615F1
Ratings: SPST, 16 Amps @125 VAC, 12 Amp @ 250 VAC, 3/4H.P. @ 125-250 VAC, 10 Amps @ 14VDCUL/CSA/VDE/RoHS approvedCutout: 1.125" x .550"Switch: 1.120" x .547"
Jr Products Labeled 12V On/Off Switch, Black - 12595 - 342-12595F1
Ratings: SPST, 16 Amps @125 VAC, 12 Amp @ 250 VAC, 3/4H.P. @ 125-250 VAC, 10 Amps @ 14VDCUL/CSA/VDE/RoHS approvedCutout: 1.125" x .550"Switch: 1.120" x .547"
Jr Products Labeled 12V 5 Pack Rv On/Off Switches - 12611-5 - 342-126115F1
Ratings: SPST, 16 Amps @125 VAC, 12 Amp @ 250 VAC, 3/4H.P. @ 125-250 VAC, 10 Amps @ 14VDCUL/CSA/VDE/RoHS approvedCutout: 1.125" x .550"Switch: 1.120" x .547"
Jr Products Labeled 12V 5 Pack Rv On/Off Switches - 12591-5 - 342-125915F1
Ratings: SPST, 16 Amps @125 VAC, 12 Amp @ 250 VAC, 3/4H.P. @ 125-250 VAC, 10 Amps @ 14VDCUL/CSA/VDE/RoHS approvedCutout: 1.125" x .550"Switch: 1.120" x .547"
Jr Products Labeled 12V 5 Pack Rv On/Off Switches - 12581-5 - 342-125815F1
Ratings: SPST, 16 Amps @125 VAC, 12 Amp @ 250 VAC, 3/4H.P. @ 125-250 VAC, 10 Amps @ 14VDCUL/CSA/VDE/RoHS approvedCutout: 1.125" x .550"Switch: 1.120" x .547"
Jr Products Kappet Screws With Covers, White, 14/Pk - 20415 - 342-20415F1
Can be used any where you need to secure an item with a screw but desire a clean, finished look. Special mounting screws included. Lifetime warranty.
Jr Products Kappet Screws With Covers, Beige, 14/Pk - 20425 - 342-20425F1
Can be used any where you need to secure an item with a screw but desire a clean, finished look. Special mounting screws included. Lifetime warranty.
Jr Products Interior Cable Tv Plate - 47785 - 342-47785F1
Interior Cable TV Plate has a 75 ohm F-Style connection. Works for any F-Style TV or satellite installations. Can be used in HD/Satellite TV connections. 2.34" x 4.50"
Jr Products Inside L-Handle - 10905 - 342-10905F1
This unit is used on the interior of popular T and L locking handles. It provides the ability to open the doors from inside the truck cap or compartment. Fits most square-shaft operating handles. Lifetime warranty.
Jr Products Hth-A Dual Voltage Rv Holding Tank Heater - Hth-A - 342-Hthaf1
Use on either fresh water or septic tank Dual voltage ready for 12V and 110V applicationsThermostatically controlled and active at 34° F24" ground wireDraws approximately 1 Amp AC and 10 Amps DCMultiple heaters may be used where needed
Jr Products Hitch Pin/Hitch Pin Clip Combo - 1144 - 342-01144F1
A replacement combination of our high quality hitch pin and hitch pin clip. Constructed of durable chromatic plated steel. Never guess if your clip or pins will fit each other, simply buy a matched set.
Jr Products Hitch Pin/Hitch Pin Clip Combo - 1074 - 342-01074F1
A replacement combination of our high quality hitch pin and hitch pin clip. Constructed of durable chromatic plated steel. Never guess if your clip or pins will fit each other, simply buy a matched set.
Jr Products Hitch Pin/Hitch Pin Clip Combo - 1065 - 342-01065F1
A replacement combination of our high quality hitch pin and hitch pin clip. Constructed of durable chromatic plated steel. Never guess if your clip or pins will fit each other, simply buy a matched set.
Jr Products Heavy Duty On/Off/Momentary-On Rv Switch - 12835 - 342-12835F1
Ratings: DPDT, 20 Amp @ 125 VAC, 15 Amp @ 250 VAC, 40 Amp @ 12 VDCUL/CSA/VDE approvedCutout: 1.25" x .84"Switch: 2.75" x 1.80"
Jr Products Heavy Duty On/Off/Momentary-On Rv Switch - 12825 - 342-12825F1
Ratings: DPDT, 20 Amp @ 125 VAC, 15 Amp @ 250 VAC, 40 Amp @ 12 VDCUL/CSA/VDE approvedCutout: 1.25" x .84"Switch: 2.75" x 1.80"
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-7903 - 342-Gsni7903F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-7145 - 342-Gsni7145F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-6687 - 342-Gsni6687F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-6642 - 342-Gsni6642F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.GSNI-6642 is used on truck caps.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-6624 - 342-Gsni6624F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5300-60 - 342-Gsni530060F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5300-50 - 342-Gsni530050F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5300-40 - 342-Gsni530040F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5300-30 - 342-Gsni530030F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5300-20 - 342-Gsni530020F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5300-10 - 342-Gsni530010F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5200-60 - 342-Gsni520060F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5200-50 - 342-Gsni520050F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.GSN5200-50 is used on truck caps.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5200-40 - 342-Gsni520040F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5200-30 - 342-Gsni520030F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5150-60 - 342-Gsni515060F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5150-40 - 342-Gsni515040F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5150-20 - 342-Gsni515020F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5100-40 - 342-Gsni510040F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.GNSI-5100-40 is used on truck caps.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5100-30 - 342-Gsni510030F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5000-60 - 342-Gsni500060F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-5000-20 - 342-Gsni500020F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-4991-60 - 342-Gsni499160F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-4983-35 - 342-Gsni498335F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-4688-40 - 342-Gsni468840F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-4033-30 - 342-Gsni403330F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-4032-28 - 342-Gsni403228F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-2600-100 - 342-Gsni2600100F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-2300-90 - 342-Gsni230090F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-2300-80 - 342-Gsni230080F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-2300-150 - 342-Gsni2300150F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-2300-120 - 342-Gsni2300120F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-2300-100 - 342-Gsni2300100F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-2200-90 - 342-Gsni220090F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Hardline Black Nitride Shaft Gas Spring - Gsni-2125-90 - 342-Gsni212590F1
Combines all the proven reliability you've come to expect from an SPD Gas Spring along with the added feature of a nitride shaft. The GSNI Gas Spring incorporates a strong annealed steel rod with a Nitride coating for added corrosion resistance, especially when used with the all composite PS130 end fitting. This gas spring is an ideal choice where exceptional quality, combined with an overall black appearance, are important for your application. GAS SPRING FIT AND SELECTIONIf you already have a gas spring installed, selecting a replacement can be as simple as A-B-C. A. Measure the extended length from center mounting hole to center mounting hole (see "A" in diagram). B. Measure the amount of piston that is exposed while extended. This is called the stroke of the gas spring. (see "C" in diagram). C. Find the extended length that is the closest to your current unit. Then use either the stroke measurement or subtract the stroke from extended and select the compressed sizes that are closest to your current spring.(The measurements do not have to be exact but the closer you can match the original the easier it will be to install.) SELECTING THE FORCE - If your current spring has a stamped label, the force should be listed within that number. Usually, the last two digits or followed by the letter N which is Newtons. One pound equals 4.4482 Newtons. This is the pounds of force being exerted to open or hold open the door or platform. It does not equal the weight of the item being lifted. Trial and error is not the best way to find that number.
Jr Products Gfci Electrical Outlet, White - 15005 - 342-15005F1
UL/cUL approved
Jr Products Fx4K Pressurepro Fx Tpms, 4 Wheel Kit - Fx4K - 342-Fx4Kf1
The first TPMS designed specifically for towables, PULSE FX delivers PressurePro's first BYOD based system, arming users with market leading tire performance management at never-before-seen value. Allowing users to leverage existing smart devices to display real time readings and alerts directly through the free, PressurePro app, FX gives users: 24/7 tire performance monitoringFive unique alerts including Tire Pressure and Tire TemperaturePush notifications and FX warning lightUnit is sealed, and can be fully submerged in waterAbility to monitor up to 40 tiresVehicle naming and storage for easy monitoring of multiple trailersFully adjustable vehicle layout and displayFully customizable baseline and alerts KIT INCLUDES:PULSE FX DeviceDynamic Standard SensorsPULSE Fixed End Power CablePULSE Dipole AntennaFX Hook & Loop Mounting Pads
